| Title | Category   |
|
|---|---|---|
| add to favorites | T41 green cutting disc size development and grinding technology is inseparable? | Cars |
| With the increasing demand for products in the market, the development of new products must start from the customer's needs, and the customer demand is to put forward higher requirements for the grinding of T41 green cutting disc size products. Unlike conventional refining processes in the past, high-speed grinding is a very high metal removal rate. If you look back at the history of grinding technology, it is not difficult to find that high-speed grinding technology began with copper blanking. In the process of recasting steel, from ingot to rolling, various defects such as cracks, wrinkles, gaps, interlayers, etc., are generated on the surface of the blank. If these surface defects are not removed before the next process, it will seriously affect the quality of the finished product. In order to achieve the highest grinding efficiency, the green cutting disc is designed with constant pressure or constant power instead of the traditional constant grinding depth and the amount of cutting. In terms of cutting discs, the working speed is increased from 35-48 m/s to 60-80 m/s by using a series of measures such as high-strength abrasive, benzene ring resin binder, hot pressing manufacturing method and reinforcing filler. The results of these efforts were very successful. By the early 1960s, in the steel renovation and casting cleaning of industrialized countries, the grinding process had completely replaced the cold chiseling process. By the middle of the 1970s, the annual sales of the rough grinding wheel had been paralleled by the fine grinding wheel, and the spindle power of the roughing machine was as high as 370 KW. Obviously, the high-speed grinding technology of the bit grinding groove is developed on this basis. Therefore, it is very beneficial to learn from the experience of the grinding wheel when developing the high-speed grinding wheel of the bit grinding groove. | ||
| add to favorites | What are the 115*1*22 cutting disc things to watch out for? | Cars |
| Because of its high efficiency, convenience, economy and other unique properties, the cutting piece has been widely used in many industries, but many people do not have a clear understanding of the specific performance of the cutting piece and the use of different cutting pieces. Today, cutting piece manufacturers Aurora Abrasives Co., Ltd. based on years of experience to share with you the correct selection and use of115*1*22 cutting disc : Cutting blades can be divided into cutting and grinding. Most of the cutting machines are fixed mobile. The power of the machine is divided into high power (>5.5KW) and low power (<3KW). The cutting speed also has high speed. Cutting (>80m / s) and ordinary cutting. In addition, cutting materials are varied, such as stainless steel, titanium alloy, ordinary steel, viscous metal, high carbon steel, non-metal, etc. The requirements are different, so it is important to choose a reasonable cutting piece. Ordinary cutting machines usually refer to fixed cutting machines, cutting machines with power <3KW and rotation speed of 2900 rpm. Ordinary cutting machines usually cut workpieces with a diameter less than 50mm. However, due to the small cutting power in order to reduce the radial frictional resistance, this When we usually choose a cutting piece with a thickness of 3.2mm, the cutting piece is thinner and has a certain elasticity, and it will feel sharper when cutting. The product of Aurora Abrasives will change the surface contact into points in order to reduce the lateral frictional resistance. Contact, and the formulation system adds lubricant, which can greatly reduce the frictional heat generated during cutting and improve the durability and sharpness of the cutting blade. | ||
| add to favorites | The secret to choosing an super thin 115 cutting disc? | Cars |
| For the super thin 115 cutting disc , I don’t know if you know it. It is made of abrasive wheel and made of abrasive and binder resin. It is widely used in ordinary steel, stainless steel and non-metal sheets, and it is based on material. Different types can be divided into fiber resin cutting sheets and diamond cutting sheets, and high-speed resin cutting sheets are also used in many industries because of their high efficiency, convenience, economy and other unique properties, but then some problems have arisen. How to choose the right super thin 115 cutting disc, what better way to do it? First, when the dicing sheet is used, it is selected depending on the occasion in which the dicing sheet is used. The cutting pieces can be divided into cutting and grinding according to the way of use. Most of the cutting machines are fixed mobile, and the power of the machine has high power and low power. Cutting speeds are also available in high speed cutting and normal cutting. In addition, the materials to be cut during cutting are various, such as stainless steel, titanium alloy, ordinary steel, viscous metal, high carbon steel, non-metal, and the like. The performance requirements of the cutting piece are different for different occasions, so it is important to choose a reasonable cutting piece. We have to choose the cutting piece according to the occasion we use, which can increase the safety factor, improve work efficiency and reduce our use cost. | ||
| add to favorites | The 4 inches China grinding disc factory introduces the structure of the grinding disc? | Cars |
| The 4 inches China grinding disc is a commonly used grinding disc tool on the market. With the expansion of the market share, the use and sales of the grinding disc are more and more, so the structure of the grinding disc is not understood by many users. Today, 4 inches China grinding disc factory will give you a brief introduction to the structure of the grinding disc. The grinding disc frame adopts a combination of upper steel plate welding and a lower cast iron bracket, and the grinding roller is mounted on the cast iron lower bracket beam. The self-sustaining of the grinding stress is beneficial to keep the rolling distance stable and reduce the noise, and the grinding rolls are horizontally arranged to facilitate the entry of the material into the grinding roll. The grinding disc is easy to be raised, and the material to be ground is not easily splashed outward. The grinding disc has a novel grinding structure, convenient and flexible operation, stable rolling distance, good grinding effect and unique grinding roller bearing structure. Reliable positioning. The operation is stable, and the roller can be quickly changed. The fast and slow rollers are driven by a three-wheeled crescent belt with a correcting deviation. Safe and reliable to use. The grinding disc has a grinding and suction device, and the self-flowing material can also be ground. The pneumatic system of the grinding disc has a unique structure and a simple gas path. The P-grinding disc has a low failure rate, and the four-piece housing is flipped over for a fully enclosed lift. The motor is placed inside the casing and has a compact structure. nice appearance. The operation is safe and reliable. | ||
| add to favorites | What is the economics of the T41 green cutting disc size? | Cars |
| With the development of technology, the development and production of cutting discs are now more and more, and the T41 green cutting disc size is typical. How can the economic efficiency of the cutting disc be improved? The T41 green cutting disc size has less wear and tear, long service life and high grinding ratio. Under reasonable conditions, good economic results can be obtained, especially for materials that are difficult to process with ordinary abrasives, and the economic effect is better. Only with the continuous improvement of the hardness of metal products in the future, the cutting disc can continuously improve itself, in order to ensure the high cutting efficiency and the best economic effect of the cutting disc on different material workpieces. Now the Henan abrasive grinding industry is constantly starting in technology. Update, I hope to develop more good products. | ||
| add to favorites | 115*1*22 cutting disc material type analysis? | Cars |
| What are the types of materials for 115*1*22 cutting disc ? Today Xiaobian gave you the following summary, I hope to help everyone: A - brown corundum abrasive, the color is brown, high hardness, high toughness. Adapted to the high tensile strength of metals, such as carbon steel, alloy steel, malleable cast iron, hard bronze. WA—White corundum abrasive, white color, hardness is higher than brown corundum, abrasive grain is easy to break, edge is sharp, cutting performance is good, grinding heat is small. Suitable for grinding hardened steel, alloy steel, high speed steel, high carbon steel, thin Wall parts, etc. SA——Single crystal corundum abrasive, the color is light yellow. Compared with A and WA abrasives, it has high hardness and toughness. It is a single-particle spherical crystal with strong crush resistance. It is suitable for grinding impervious steel and high vanadium high-speed steel. Other materials with high toughness, high hardness and workpieces with easily deformed burns. PA——Chromium corundum abrasive, the color is rose or purple, the cutting edge is sharp, the edge retention is good, the durability is high. It is suitable for the workpiece with low surface roughness value of grinding tool, measuring tool, instrument, thread and so on. GC - green silicon carbide abrasive, green color, high hardness, brittleness, sharp abrasive, a certain thermal conductivity. Suitable for grinding cast iron, brass, lead, zinc and rubber, leather, plastic, wood, ore. | ||
| add to favorites | T41 green cutting disc size installation requirements? | Cars |
| Due to the rapid development of the processing industry, many steel and industrial products need to be reprocessed, which has led to the development of the cutting sheet industry, which has high requirements on the performance, material, use time, sharpness and adhesion of the cutting sheet. And after research and innovation, the T41 green cutting disc size has better dimensional performance. Through data analysis and research, the T41 green cutting disc size installation requirements are discussed. According to the research, before installing the cutting disc, the marking of the cutting disc must be checked first. The grinding wheel with unclear or no marking must be re-tested by the rotation. Otherwise, it is easy to get confused. It is necessary to understand the working line speed of the green cutting disc. When a cutting piece with a line speed of 50 m/s is attached to a machine with a working line speed of 80 m/s, it is easy to break. Before installation, tap the cutting piece with a wooden hammer. If it makes a crisp sound, it means ultra-thin cutting. The quality of the film is qualified, otherwise it may indicate that there may be cracks in the grinding wheel. This kind of grinding wheel cannot be used. | ||
| add to favorites | The development trend of super thin 115 cutting disc? | Cars - Economy cars |
| With the increasing variety of products in the machinery industry and the increasingly advanced technology, more mechanical products need to be processed. Usually, the processing of each mechanical component first needs to be formed by cutting the sheet, and then the subsequent grinding and polishing. Chamfering, after a series of processes, finally become a qualified mechanical component. The cutting blade is used as an assistant in the processing of mechanical parts. His quality, reliability, efficiency and safety are the focus of each machining center in purchasing. In the face of the development trend of the future machinery industry, then the u super thin 115 cutting disc will be seen together in the future development trend of the mechanical industry. First, the hardness of the cutting piece, more and more new metal products in the future, then the hardness requirements of the cutting piece product are also more and more, the hardness of the cutting piece product determines everything of the product, currently, by superhard abrasive The high precision and high efficiency grinding effect has been widely recognized. | ||
| add to favorites | High power 115*1*22 cutting disc selection? | Cars |
| High-power 115*1*22 cutting disc usually use a cutting power of more than 5.5 kW and a rotational speed of 2800 rpm, which is a large diameter for cutting workpieces. Because the torque force during cutting is large, the damage to the cutting piece is also relatively large, so the cutting piece is required to have a certain rigidity. We usually use a 3.8 mm thick cutting piece. As the cutting diameter is larger, the resistance of the cutting piece is also increased, and the temperature of the cutting surface is high, so it is very important to lower the cutting temperature. If necessary, add water to cool when cutting. The experiment proves that if the water is cooled during cutting, the durability of the cutting piece can be improved by 1.5-2 times. However, in some occasions, there is no condition for water cooling. Therefore, when the high-power cutting piece is produced by Jixiang Abrasives, the powder coolant is added according to the formula to reduce the temperature generated during cutting, and the life of the cutting piece is improved. | ||
| add to favorites | How to distinguish the T41 green cutting disc size? | Cars |
| T41 green cutting disc size is a commonly used cutting piece, so how do users distinguish different cutting pieces when choosing? The cutting piece belongs to the grinding wheel and is made of abrasive and binder resin for cutting ordinary steel, stainless steel, and non-metal sheets. It is made of glass fiber and resin as the reinforced bonding material. It has high tensile, impact and flexural strength. It is widely used in the production of ordinary steel, stainless steel and non-metal. The excellent materials and exquisite craftsmanship guarantee different materials. High cutting efficiency and optimum economics of the workpiece. | ||
| add to favorites | What are the characteristics of the super thin 115 cutting disc? | Cars |
| The super thin 115 cutting disc has the following qualities: High-precision, high-life, high-efficiency cutting and grooving, electroforming ultra-thin cutting sheets are thinner than electroplating ultra-thin sheets, can be made thinner, can be as small as 0.015mm, and electroplating is impossible. In the bending resistance, the sharpness is much better than the plating method. Reduce cracking, chipping, gaps, and product lengths. Ultra-thin cutting blades are suitable for: cutting quartz glass tubes, optical glass, magnetic materials, ceramics, electronic components, crystal, ferrite, lithium niobate single crystal, alumina and so on. Features: The use of the whole diamond without a substrate; the use of special bonding agent with good sharpness and shape retention, especially suitable for combination cutting. Type: electroforming method, no substrate, diamond, ultra-thin cutting piece | ||
Please register or log in.
Powered by Noah's Classifieds 3.2.0 -
try Noah's Classifieds V8 e-commerce enabled