[Noah's Classifieds] - Advertisements of user yanghuim

Please register or log in.

Advertisements of user yanghuim
	Title	Category
add to favorites	What should you pay attention to when purchasing China cut off disc?	Cars
Due to its technological development, China cut off disc are now very popular among users, but for some users who have not touched the cutting disc before, they do not know what to pay attention to when purchasing the cutting disc. Today, Aurora Abrasives will give you a summary of the issues to be aware of when purchasing China cut off disc . Grinding rate of the first product Grinding ratio is “Bringing ratio”. The grinding ratio is the cutting efficiency of the cutting disc. The less the disc loss is, the more the workpiece is cut. The higher the grinding ratio, the better the performance of the cutting disc. Second look at product features The dressing of the super-hard abrasive cutting disc is different from that of the ordinary cutting disc, and the trimming process is divided into two stages of shaping and sharpening. The shaping stage means that the working surface of the grinding wheel has the required geometric accuracy of the surface. The sharpening stage means that the excess bonding agent around the super abrasive grains on the working surface of the grinding wheel is removed by sharpening so that the abrasive grains are exposed to the desired height so that the working surface of the grinding wheel has good grinding performance. The above is some of the problems that need to be paid attention to when purchasing the cutting discs. I hope that you can choose to better cut the disc equipment.
add to favorites	Maintenance of the Agricultural use Tractor Mounted Rice/Wheat Seeder gearbox installed?	Cars
With the advent of Agricultural use Tractor Mounted Rice/Wheat Seeder, the traditional artificial seeding method has been broken, making the planting work less laborious and making people feel that farming is a relaxing and enjoyable pleasure. Due to changes in production and breeding ideas, the density of the planter has also changed, resulting in some innovative planter equipment, such as gearbox maintenance. So how should the seeder gearbox be maintained? The first replacement of the transmission lubricant is carried out 30 hours after the initial operation and then replaced every 1500 hours. When replacing the lubricating oil for the first time, remove the screw plug of the bottom oil drain hole and the screw plug of the top air hole, drain all the oil, and then re-tighten the screw plug to inject the lubricating oil into the tank. The no-till seeder belongs to Farmland protective machinery, which integrates crushing, rotary tillage, sowing, covering and repressing, and can complete 6 kinds of operations at a time. The use of no-till seed drills for mechanized conservation tillage can reduce operations and reduce agricultural costs. Moreover, it has obvious water-saving and drought-resistance effects, and the implementation of no-tillage sowing greatly reduces the number of crops that can be harvested and can increase production and increase income.
add to favorites	Professional Customize Corn/Soybean Precision Planter manufacturers?	Cars
A planter is a small machine used in dry fields. Applicable to all ridge crops in dryland crops. It is the first choice for farmers' friends to realize agricultural mechanization. The gearbox produced by the regular enterprise is selected, and the high-quality brand-name gasoline engine is used as the supporting power. Easy to start, light and durable. The overall board design, one-shot molding, is sturdy and durable. Bold handles. User-friendly high-quality hand throttle design. The new model adds a high and low neutral gear clutch function. The unique main wheel design does not slip, and the dust is less, reducing the leakage to the gearbox and entanglement. Today, Aike, the manufacturer of professional Customize Corn/Soybean Precision Planter , will introduce the use characteristics of this planter: The quality is stable and reliable. Both men and women can use it. The quality is stable and reliable. Both men and women can use it. Moreover, this type of planter is not only easy to operate but also stable in production. It is the first choice of many users now. Aike is a professional manufacturer of seeding machines. Our seeders are of good quality and affordable. Welcome new Old users come to buy.
add to favorites	What is the principle of China abrasive tools for metal?	Cars
Metal grinding tools should be a device that everyone is familiar with in our lives. Of course, it plays an important role in life, but many users don't know the principle. So today, Aurora abrasives manufacturers describe China abrasive tools for metal . Information about the principle of the tool equipment. With the continuous improvement of the automation degree of grinding tools, the structure of machine tools has become more and more complicated, and the technical requirements for equipment management and operators have become higher and higher. Therefore, many resin grinding wheel enterprises have experienced the shortage of senior technicians. Maintenance technology can't keep up. Moreover, with the improvement of raw material performance, the increase of labor costs, the further development of market environment and the mutual merger and expansion of large and medium-sized companies, fully automatic resin grinding wheel equipment will also be widely used. When it is used, the company faces more sophisticated production equipment. If it can't deal with the problem quickly, it will have a bad impact on the tight and rapid production environment. Especially in the flow mode, if the technician can recover the machine one minute earlier. Production is a kind of benefit for the enterprise. We use professional and power to protect our production equipment. Equipment management personnel - the company's steel guards. Many factory equipment management personnel will complain about the heavy workload, management is a false name, just A maintenance worker. The reason for the company system is actually the responsibility of the maintenance personnel. Facility managers have to wait until the machine is broken before going to work, always passive repair, do not know how to take the initiative to prevent, it can only be called a maintenance man, can not be called device management.
add to favorites	What is the classification of the green cutting disc?	Cars
Users who have used the cutting piece have a certain understanding of the cutting piece, but how many people know about the classification of the cutting piece? Today, the aurora abrasive grinding tool uses the green cutting disc as an example to give a brief introduction to the cutting piece. Classification problem. What is the classification of the green cutting disc? Classification of cutting sheets, which are subordinate to grinding wheels, made of abrasive and binder resin for ordinary steel, stainless steel, and non-metallic sheets. With the development of the future machinery industry, More and more cutting-edge industry is beginning to approach this market. Many companies have begun to update their product technology, hoping to develop more good products. The cutting piece is made of glass fiber and resin as the reinforced bonding material. It has high tensile strength, impact resistance, and bending strength. It is widely used in ordinary steel. Stainless steel metal and non-metal production and cutting, excellent materials. Exquisite craftsmanship guarantees High cutting efficiency and economical effect of different material workpieces. In the face of more and more new metal products in the future, the hardness requirements of the cutting piece products are also increasing. The hardness of the cutting piece products determines everything about the products. At present, the high precision and high efficiency brought by the super hard abrasive tools. The grinding effect has been widely recognized.
add to favorites	What are the precautions for green cutting disc installation?	Cars
The wide application of green cutting disc makes them occupy an important position in industrial production. The correct installation of cutting sheets is directly related to the safety in the production process. Now, the manufacturers are talking about the green cutting disc installation precautions. : 1. Before installation, use a wooden hammer to tap the cutting piece. If a crisp sound is heard, the quality of the ultra-thin cutting piece is qualified. Otherwise, there may be cracks in the grinding wheel. This type of grinding wheel cannot be used. 2. Before installing the cutting piece, the marking of the cutting piece must be checked first. The grinding wheel with unclear or unmarked mark must be re-tested by rotation, otherwise, it is easy to be confused. 3. It is necessary to know the working line speed of the cutting piece. If the cutting piece with a working line speed of 50 m/s is attached to a machine with a working line speed of 80 m/s, it is easy to break. 4. The flanges on both sides are the same shape. The diameter of the flange is generally half the diameter of the resin grinding disc, and the inner side should have a concave groove. Between the end face of the grinding wheel and the flange, it should be padded. Elastic cardboard or leather with a thickness of about 1 to 2 mm. Oil-resistant rubber gasket. The diameter of the gasket should be slightly larger than the outer diameter of the flange.
add to favorites	Introduction and application of free sample cutting discs?	Cars
Nowadays, with the increasing demand for the abrasives industry, the development of the abrasives industry is getting faster and faster, and thefree sample cutting disc are used as cutting equipment commonly used in the abrasives industry and are also used by many users. The cutting disc is made of resin fiber material, which is not easy to be broken, safe to use, and the cutting performance is particularly remarkable. It is most suitable for cutting stainless steel, titanium alloy, nickel alloy, general metal material. Unhardened steel, cast iron, alloy cast iron, carbon steel. Alloy tool steel. Quenching just. Castings and high-hardness materials such as hot brittle materials. Today Aurora abrasives manufacturers share the introduction and application of free sample cutting disc. The cutting disc has two kinds of dry and wet cutting methods, which makes the cutting precision more stable, and its cutting is not black, beautiful. It is characterized by small machine load, fast cutting and sharp and durable. Nowadays, such cutting discs are often used for stainless steel tubes, capillaries, glass tubes, quartz tubes, automobile exhaust pipes, brake wires, tungsten wires, molybdenum wires, copper wires, and other pipe and wire cuts, and it is for special steels. The cutting and the slotting of the workpiece have a good effect.
add to favorites	What are the characteristics and application areas of the T41 green cutting disc size?	Cars
The size of the T41 green cutting disc size is a cutting device commonly used in the abrasives industry today. It now has a place in the market and is increasingly popular with users. The cutting disc refers to the working layer of the outer ring of the grinding wheel, and the central part is the high-strength rigid metal material, also known as the outer ring-shaped cutting piece. The following Aurora abrasive grinding tool manufacturers will introduce to you, the T41 green cutting disc size is mainly What are the characteristics and application areas? 1. Suitable for single piece or multi-knife combination cutting. 2. Excellent grinding ability and high wear resistance, ensuring a long service life of the blade. 3. The high hardness of the bonding agent makes the blade have the characteristics of high rigidity so that the blade does not deform during the cutting process, thereby ensuring the perpendicularity of the cutting surface. 4. Through the fine adjustment of the concentration and particle size of the abrasive, it can have good cutting efficiency under the premise of meeting the requirements of the clean surface of the cutting surface. 5. Advanced and scientific processing methods and strict process control to ensure the high dimensional accuracy of the blade. 6. The precise classification of the bonding agent satisfies the requirements for the special blade for processing different materials.
add to favorites	How to write information when purchasing China abrasive tools for metal?	Cars
With the development of the Internet, many companies now publish their product information online for sale. The same is true for metal grinding tools. In order to have a bigger market and more customers, metal grinding tools will put their own product information. Publish to the B2B platform or other websites. But in order to make it possible for buyers to better choose their own products or contact the merchants to fill out their own information, today, we will use the China abrasive tools for metal to give you an example. 1. What materials should be polished by China abrasive tools for metal ? This is the first step in the purchase of metal grinding tools. It is also the most direct problem. For example, if you want to buy a metal grinding tool, it is grinding metal or other materials. Similar problems can be used to display the manufacturer's production materials directly in the sales of metal grinding tools. In front of the manufacturer. 2. Write the required output in the title or content of the metal grinding tool. Buying Metal Grinding Tool Information If you can provide daily production or time production in the content area of the title or purchase information, you can save a link in the sales communication, no need to let the seller waste time asking the buyer for the output. Moreover, the manufacturer can provide the metal grinding tool production parameters as a solution reference. The above points can help buyers better choose the right grinding tools.
add to favorites	T41 green cutting disc size production process?	Cars
The production process of T41 green cutting disc size is not complicated, but we don't know much. With the development of technology, the market for cutting discs is gradually developing. The market for cutting discs will be more broad in the future, and we will also see the development of cutting discs in the later stage. It is also better. Let's take a look at the production process of the cutting disc today. Cutting disc production process: The cutting disc should have a high purity and a certain particle size composition, so the crystal blocks produced by the smelting furnace must be processed. The main content of the processing is through crushing, sieving and water selection. Particle size, by washing with water or acid and alkali, magnetic separation to enhance purity, and some need to be treated. If you still don't understand it well, you can visit our cutting board manufacturers to see the specific production process. We are all external.
add to favorites	China abrasive tools for metal should be cleaned frequently？	Cars
After using the China abrasive tools for metal for a period of time, in order to ensure that the working environment dust emission concentration is lower than the environmental protection requirements, metal grinding tools are usually equipped with dust collectors. Most customers choose bag dust collectors. Clean up, otherwise it will block the bag and affect the dust removal effect. Many powder processing plants, because of the pursuit of profit, often overlook the China abrasive tools for metal o clean the dust collector. When the grinding tools are in normal production, the workers are armed with wooden sticks and other instruments to beat the inflated bags. In order to knock down the material attached to the inner surface and fall into the dust collector below, this method is unreasonable. When used, it is easy to cause damage to the bag itself, and the artificial force is uncontrollable, the most obvious It is to smash the bag. At this time, because it is in normal production, the dust will leak out to the whole workshop. Not to mention dust removal, there is no way to work. So what method is used to calculate it correctly? After our staff's summary methods are high frequency vibration, chemical cleaning, low temperature water cleaning, drug soaking, hot air drying, etc., these methods are a bit difficult for some processing plants, after all, do this powder processing business, buy and use It is impossible to use such a professional method to clean the dust collector.
add to favorites	What are the installation points for the free sample cutting disc?	Cars
The free sample cutting disc is a commonly used sharpening tool. It should be paid attention not only during use but also should pay attention to some points during installation to avoid some problems during use. So which four points should you pay attention to when installing free sample cutting disc? 1. Before installing the cutting disc, the working line speed must be calibrated. Grinding wheels with unclear or unmarked signs shall be re-tested by rotation. 2. The flanges on both sides are the same in shape. The diameter of the flange is generally half the diameter of the cutting disc, and the inner side should have a concave groove. Between the end face of the grinding wheel and the flange, a thickness is required. Approximately 1 to 2 mm of elastic cardboard or leather, oil-resistant rubber gasket, the diameter of the gasket should be slightly larger than the outer diameter of the flange. 3. Between the inner hole of the cutting disc and the outer circle of the grinding wheel shaft or the flange, it should not be too tight, otherwise it will be heated and expanded during grinding. It is easy to rupture the cutting disc, and it should not be too loose, otherwise it will easily lead to eccentricity and loss of balance. Causes vibration. Generally, the matching clearance is 0.1~0.8mm, and the high-speed clearance is smaller. 4. When clamping with flanges, the diameter of the two flanges should be equal, and the outer diameter should not be less than 1/3 of the outer diameter of the grinding wheel. Apply a thick cardboard or oil-resistant rubber between the flange and the end face of the grinding wheel to make the pressure evenly distributed. The tightening force of the nut should not be too large, otherwise the grinding wheel will be broken. Note that the direction of the tightening thread should be opposite to the direction of rotation of the grinding wheel, that is, when it is rotated counterclockwise, use the right-hand thread, so that the grinding wheel will tighten the tightening force under the action of the grinding force.
add to favorites	What about green cutting disc?	Cars
The green cutting disc is now also a type of cutting piece that is very popular among users in the market, but for some newly-entered users, the industry of the cutting piece is not well understood, so there is not much knowledge about the cutting piece. Today, the Aurora Abrasives will give you a brief introduction to the cutting piece. The cutting sheets are made of high-strength resin and preferably special abrasives, which allow large linear speeds, all exceeding 50 m / s, which are not brittle. The cutting is sharp, the cutting heat is very small, and the sample heat affects the layer shallowly, thus minimizing interference. Cutting sheets are widely used in machinery, automobile, shipbuilding, metallurgy, chemical industry, etc., and can also be used in iron decoration and equipment repair of modern houses and factories. Suitable for general metal, stainless steel, broken fire steel, tool steel construction metal, cast gray iron, hard cast iron metal. The super-hard cutting piece has less wear, long service life and high grinding ratio, and can obtain good economic effects under reasonable use conditions, and has better economic effect on materials which are difficult to process with ordinary abrasive materials.
add to favorites	How to choose a free sample cutting disc?	Cars
With the development of the abrasives industry, the cutting disc industry is now also occupying a certain proportion in the Chinese market, especially the free sample cutting disc， which is very popular with some users. But for some novice users, in the selection of cutting discs There are always some problems encountered. Today, Aurora Abrasives will give you an analysis of how to choose a cutting disc. When choosing a free sample cutting disc, you should pay attention to the following points: 1. Good uniformity appearance and no cracks are the basic appearance of high quality cutting discs; 2, excellent packaging and printing anti-counterfeiting barcode is the difference between the factory products and counterfeit goods; 3, the general rule of cutting and polishing is to reduce the amount of iron, the low wear is the grinding wheel is too hard, the amount of iron to wear is small, the wear is too poor, the quality of the inner quality is as little as possible, the maximum amount of iron removal, At the same time feel good; 4. If you have a large amount of cutting discs, it is impossible to have the cutting disc that is most suitable for you on the market, so if you can, it is best to contact the manufacturer directly.
add to favorites	T41 green cutting disc size use common sense?	Cars
With the development of the abrasives industry, the use and development of cutting discs is becoming more and more rapid. Among them, the T41 green cutting disc size is used more in the cutting disc industry. The use of this type of cutting disc is not only because of its good effect. And it is more convenient to use. So for the user to better use the cutting disk, you must first understand the common sense of the switch disk. First, the inner diameter is damaged. The main cause of this phenomenon is improper assembly. The cutting piece is used as a grinding disc and the flange is partially lost. Second, if the tangential line is not straight or damaged, this is mainly due to improper diameter of the assembly flange, the assembly flange is not working well, the machine is not working properly; or the workpiece is improperly clamped, the cutting pressure is too large, the slice is too Caused by thin. Third, the main cause of discoloration of the cut surface is that the slice is too hard, and the cross-sectional area of the object to be cut is larger than the slice diameter. There is also a result of long cutting time and low motor power. Fourth, if its wear is large, this is mainly caused by the machine speed is too large and the peripheral speed is too fast. In addition to this reason, it is necessary to note that if the cut surface is white, the slice is too soft. If the cut surface is discolored, the degree of consolidation is too hard. Fifth, the rim tear, and this phenomenon is mainly caused by the use of the cutting piece as a grinding piece, that is, caused by improper use. Or the workpiece is caught by the spring due to improper operation of the machine.
add to favorites	What are the factors affecting the production capacity of China abrasive tools for metal?	Cars
Compared with other types of mills, China abrasive tools for metal have high efficiency and energy-saving performance. When the fineness of the finished product and the motor power are the same, the output of the ball mill is more than double. China abrasive tools for metal wear parts have a long service life, and the grinding rolls and grinding rings are made of special materials, so that the utilization degree is greatly improved. However, there are always problems in the use of the grinding tools, which affect the production of the grinding disc tools, resulting in a decrease in production. The grinding tool scrapes the material through the blade and falls between the grinding roller and the grinding ring. The falling material is milled and crushed by the pressing rotation of the grinding roller on the grinding ring. Therefore, the hardness of the material is harder, and the grinding roller is The greater the friction, the less easily the material is broken and the grinding powder is slow, the production capacity is reduced, and the wearing parts are easily damaged. When selecting materials, it is necessary to select materials suitable for the model and parameters of the mill for processing and production to ensure stable production efficiency.
add to favorites	What are the benefits of using a free sample cutting disc?	Cars
With the development of the abrasives industry, there are more and more types of cutting discs on the market, but among many cutting discs, many users prefer the free sample cutting disc. Why do users like to use this type of cutting? What about the benefits of using a free sample cutting disc? Some users who have used this type of cutting disk will find the following benefits: 1.Without filling, can play a good grinding and cutting efficiency; 2.With air cooling effect, can significantly avoid the phenomenon of heating and burning on the working surface; 3.Safe, sharp, wear-resistant, non-heating, non-burning, power saving, labor saving, time saving, high efficiency and economical and practical; 4.Moderate softness can be applied to the grinding and cutting operations of curved work; 5. At the same time of work, the burrs of the working surface are removed, and the working surface is smoothed; 6.To meet the customer's requirements for non-standard customization, can be customized according to the customer's drawings or samples.
add to favorites	What is the method for the free sample cutting disc slicing?	Cars
The free sample cutting disc is a popular cutting disc device in the cutting disc industry. It is now popular and popular among users. But everyone knows that even the best equipment has problems, thefree sample cutting discis the same, then when the cutting disc is sliced how do users correct the cutting piece when there is a problem? What are the finishing steps? 1. The hand grinder table is fed longitudinally to the hand wheel to bring the diamond close to the end face of the slice. 2. Install the grinding section on the round hole of the grinding wheel dresser perpendicular to the axis, adjust the position of the round bar of the slice dresser, make the diamond tip lower than the center of the polishing plate 1-2mm, and fasten the bracket. 3. After the diamond is in contact with the end face of the slice, the longitudinal feed of the table is stopped, and the hand slicer is fed laterally to the hand wheel to reciprocate the diamond back and forth at the end face of the slice. After multiple feeding and trimming, the end surface of the slice is ground into a concave plane, and the edge of the slice transmission line is left with a clip H=3 mm. Pay attention to the correction of the polished sheet: 1. Pay attention to the rigidity of the diamond rod to prevent the diamond from vibrating during correction. 2. When the correction is made, the manual feed of the table should be slow, and pay attention to the width of the control clip. 3. Generally, the end face of the grinding wheel should be trimmed first, and then the circumferential surface of the grinding wheel should be trimmed.
add to favorites	What is the abrasive material of the T41 green cutting disc size?	Cars
With the increasing market size of T41 green cutting disc size, there are many companies that produce cutting discs on the market. The size of the cutting discs produced by different companies is different from the materials used, and for some users who have not touched the cutting discs. I don’t know what the basic material of the production cutting disc is. Today, the professional cutting disc manufacturer Aurora Abrasives gives you an analysis of some abrasive materials for the production of cutting discs. Commonly used abrasives for T41 green cutting disc sizeinclude brown jade (A), white corundum (wA), black corundum (BA), black silicon carbide (c), etc. The most commonly used is brown fused alumina, because brown fused alumina has high hardness and toughness. The particles are sharp, the applicability is strong and the price is lower than other abrasives. Brown fused alumina is divided into primary sand and secondary sand according to its reduction during smelting, mainly in chemical composition: Al2O3 content of primary sand is ≥94.5; Al2O3 content of secondary sand is <94.5%; generally 85% Left and right, and the Fe2O3 content is 4 to 5%; therefore, the secondary sand hardness is lower than that of the primary sand, but the price is also low; the brown corundum is suitable for the processing of various carbon steels and general alloy steels; the white corundum is higher in hardness than the brown corundum. It has large brittleness and small grinding heat. Because of its high price, it is used for heat deformation of workpieces. It is also used as a mixed abrasive for special material processing. The content of Al2O3 in black corundum is 70-85%, and the content of Fe203 is 7-9. Low hardness, poor cutting force, but the price is also cheap; black silicon carbide has high hardness and good brittleness, sharp cutting edge, good self-sharp performance, good thermal conductivity, and advantages in processing non-ferrous metals, plastics, rubber and cast iron.
add to favorites	How to develop the China abrasive tools for metal market in the future?	Cars
How to develop the China abrasive tools for metal market in the future? Metal grinding tools are the development trend of future grinding equipment. So how is the future development of the metal grinding tool market? The following Aurora analyzes the development market. With the continuous development of the society, the grinding tool market is quietly changing. Some rough processing small enterprises will gradually withdraw, and large-scale grinding tool production lines will be scaled up. This is the main trend of the current and future powder market. It is necessary to know that mineral resources are now gradually classified as state-owned, that is, they do not want to be indiscriminately opened, or that large-scale processing enterprises are required to carry out scale production, so that on the one hand, the quality of processed products can be guaranteed, and on the other hand, it is easy to manage. Large-scale production, it is necessary to use metal grinding tools, manufacturers that can produce large-scale equipment with strength, are old-fashioned enterprises, can guarantee the quality, and can also strengthen the confidence of powder enterprises. Then how to position the metal grinding tool market, can now be said to be a large grinding tool, basically at least 6 tons per hour, said large, on the one hand, the equipment is bulky and heavy, on the other hand, the price is high, so Large-scale products, there are not many production capacity in the market. Therefore, the development of China abrasive tools for metal market is still very strong in the future.